From Webshed
Revision as of 20:01, 7 September 2011 by WikiSysop (talk | contribs)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigationJump to search

Getting a FUNcube Dongle running on Linux

My FUNcube Dongle, with an SMA <-> BNC converter attached

This is how I got my FUNcube Dongle (FCD from here on in) working under Linux on a Samsung N130 Netbook PC using Quisk SDR software. The Linux distro installed is Ubuntu 11.04, but instructions should be very similar for any recent Linux distro.

Check the FCD is detected

First of all insert the FCD into a USB port and determine that it is detected:

 $ lsusb
 Bus 005 Device 003: ID 04d8:fb56 Microchip Technology, Inc.

The FCD uses a Microchip PIC to handle USB connectivity, so the lsusb command lists the FCD as a Microchip Technology, Inc. device. As long as the hex identifier, 04d8:fb56, is listed correctly then the FCD is being detected and not confused with some other device also connected to USB.

Install QTHID FCD control software

At this point it is a good idea to download the latest version of the QTHID FCD control software and check this this can communicate with and control the FCD. I found I had to start the qthid software with extra permissions to access USB, this is easily achieved

  $ sudo ./qthid
QTHID v3 Software running under Linux

As long as the software says "FCD is active" then all is well, skip to the next step - setting up ALSA. If QTHID says "FCD not detected" but the FCD is listed by the lsusb command above, then you may need to update the firmware on your FCD. IN which case, get the older 2.2 version of the QTHID software (this can talk to older FCD firmwares) and use it to upload the latest firmware from the main FCD website. The following, contributed by Robin Gape G8DQX explains how to update the FCD firmware.

Upgrade FCD firmware if needed

Firmware update from 18b
This procedure assumes that the procedures above have been performed, and that the FCD is recognised.

  • Download the new firmware image (18f) from the FCD website, and save the file export18f.bin in a known location (right click and select “Save link as...” or similar in the browser)
  • Start QTHID (version 2.1 or 2.2)
QTHID v2.2 Software required to upgrade older FCD firmwares
  • Plug in the FCD whose firmware is to be updated
  • Note that the presence of the FCD is acknowledged by QTHID

Do not proceed if the step above is not successful

  • Click the “Switch to bootloader” button
  • The presence icon will change colour to orange, with the text “FCD bootloader”
  • Click the “Update firmware” button, and select the firmware image file saved above
  • The firmware will now be updated.
  • This takes a long time, several minutes.

Be very patient, even if nothing appears to be happening

  • Eventually a dialogue box appears with the text “Firmware successfully written”
  • Click on the OK button
  • And switch back to normal mode with the “Switch to application” button.
  • When this fails, unplug and replug the FCD
  • QTHID will now show “FCD is active”
  • QTHID version 3 may now be installed & used to control all the parameters of the FCD

Check ALSA configuration

Next check how ALSA (Advanced Linux Sound Architecture) is identifying the FCD (The FCD pretends to be a soundcard)

 $ cat /proc/asound/cards
 0 [Intel          ]: HDA-Intel - HDA-Intel
                         HDA-Intel at 0xf044000 irq 43
 1 [default       ]: USB-Audio - FUNcube Dongle V1.0 at usb-0000:00:id.3.1

This means that ALSA is calling the built in soundcard "hw:0" and the FCD "hw:1", this is all the information we need to configure Quisk.

Install Quisk SDR software

Get and install Quisk as documented here. Quisk requires a configuration file to enable it to communicated with the FCD, this is mine:

  sample_rate = 96000                  #ADC Hardware sample rate
  name_of_sound_capt = "hw:1"    #Determined from ALSA
  name_of_sound_play = "hw:0"    #Determined from ALSA
  channel_i = 0
  channel_q = 1


Start quisk

 $ ./ -c

The Quisk software isn't fully polished or able to control the FCD directly, so you need to run it in conjunction with QTHID to control the FCD. Set Quisk frequency to a nice round number and then it's easy to calculate the offsets needed for tuning with QTHID.